64-66 Ford Mustang FiTech 600HP EFI Fuel Injection Gas Tank Conversion Kit 90ohm
The mounting straps are included. This kit has everything you need to convert your classic Mustang to modern fuel injection while revamping your entire fuel system at the same time. Ditch your finicky, leaking, or worn our carb for a FiTech setup that will start every time you turn the key! FiTech Easy Street EFI Features. Die cast body with classic gold finish. Four (4) flow matched 600 HP injectors. For non-boosted, naturally aspirated applications. For applications producing 200-600 horsepower. Initial setup is quick and easy. Simple touch screen selections get you up and running in minutes. Basic install can be done with just 4 wires and 2 sensors to install. 1 BAR internal MAP sensor. The ECU is mounted on the throttle body so there are NO external boxes or harnesses to clutter up your engine compartment or under dash. This saves you a huge amount of time and keeps things simple and neat. Throttle bodies have a completely universal base to fit any 4-barrel manifold. Throttle linkage suits most transmissions. Built-in fuel pressure regulator. Includes handheld controller with cable and windshield mount. O2 sensor with bung. Fits: 1964-66 Ford Mustang. EFI style internal baffling with extra large 4.8 liter dual tube baffled fuel tray to prevent fuel pump starvation. Uses aftermarket 5-bolt hole senders (included). Correct filler neck included. Dimensions: 32-3/4″ x 24-1/2″ x 7-1/2. Flow rate of up to 255 LPH. Supports up to 600HP. All metal components are yellow zinc-plated. 1/4 NPT supply and return line size. 40-100 PSI operating range. Heavy gauge mounting plate. CPP LS Conversion Fuel Filter/ Regulator Kit Features. 25 feet of high-pressure fuel injection hose. (1) 3/8 fuel filter feed line fitting. (1) 5/16 fuel filter/regulator return line fitting. (2) 3/8 female to -6AN male straight filter fittings. (2) 45-degree -6AN female to 3/8 hose fittings. (6) straight -6AN male to 3/8 hose fittings. LS fuel filter/ 58psi Regulator. 255LpH maximum fuel pump flow rate. CPP 90-ohm Fuel Tank Sending Unit Features. 0-90 ohm sending unit. 6-24 volt DC operation. Works with negative or positive ground electrical systems. Fully adjustable, will fit 6″ to 24″ deep fuel tanks. Includes (5) special O-ring screws and gasket. Works with most aftermarket fuel gauges including VDO, AutoMeter, Classic Instruments, Omega, and Stewart Warner. FiTech Fuel Injection is rounding out the street line with the all new Easy Street 600hp system. The street series includes the 150-400hp Go Street and the 200-800hp Mean Street, now were adding the 250-600hp Easy Street system! Pre-programmed with bolt-n-go technology for out of the box performance with minimal input required. Easy tach input, reads tach signal from COIL, HEI, CDI, and many other ignition brands (no timing control). For non boosted engines naturally aspirated applications only. This complete fuel injection gas tank conversion kit comes with everything you need to modernize your fuel system on your 1964-66 Mustang and includes a brand new 16-gallon EFI fuel tank, EFI fuel pump kit with installation accessories including a complete fuel line kit and sending unit. The fuel line kit includes. 25-feet of properly rated fuel injection hose and all the correct fittings to plumb your fuel lines from the fuel pump forward along with a 58psi fuel pressure regulator/ filter that is perfect for anybody dropping an LS into their vehicle or who happen to be running an aftermarket fuel injection unit. All the fittings feature a reusable spin-lock connector that does not require specialty tools to disassemble. The sending unit is. Adjustable and will fit 6-24 deep fuel tanks and will work with 6-24V electrical systems as well as negative or positive ground systems too. The FI fuel pump can support up to 600 horsepower and ar. E quiet and reliable and a must for your fuel injected engine. Orders placed Friday and through the weekend will be processed Monday (excluding Holidays). The item “64-66 Ford Mustang FiTech 600HP EFI Fuel Injection Gas Tank Conversion Kit 90ohm” is in sale since Monday, December 7, 2020. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Air Intake & Fuel Delivery\Fuel Inject. Controls & Parts”. The seller is “classic_performance_cpp” and is located in Placentia, California. This item can be shipped to United States.
- Custom Bundle: Yes
- Interchange Part Number: MU-HT
- California Prop 65 Warning: Cancer and Reproductive Harm
- Placement on Vehicle: Front
- Manufacturer Part Number: MU6768CFIT-K
- Brand: Classic Performance Products CPP
- Fitment Type: Performance/Custom
- Mounting Hardware Included: Yes